Standard hydraulic hoses commonly fall short on job sites: poor oil resistance leads to swelling, the outer cover wears through quickly, high pressure causes bulging and leaks, and temperature swings trigger cracking and aging. Frequent replacements raise consumable costs, delay project timelines, and create safety risks for operating equipment.
Our oil-resistant and wear-resistant hydraulic hoses for construction machinery uses a three-layer composite structure — premium nitrile inner tube, high-tensile steel wire braid reinforcement, and an abrasion-resistant outer cover — built specifically to address the most common failure points in heavy-duty working conditions.
If you need hydraulic hoses matched to your construction equipment's high-pressure systems, or custom-sized oil-resistant abrasion-proof hydraulic hoses for construction machinery, contact our factory for a tailored selection and quote.
Designed specifically for the demanding conditions of construction and heavy equipment, this hydraulic hose solves the core weaknesses of conventional hoses: poor oil compatibility, rapid wear, pressure-related failures, limited temperature tolerance, and short service life. It handles the continuous high-intensity operation typical of heavy machinery.
Built with refined production processes and quality raw materials, this oil-resistant and wear-resistant hydraulic hoses for construction machinery delivers consistent pressure handling, oil resistance, abrasion resistance, and weatherability. It prevents the leaks, pressure drops, and line failures that disrupt hydraulic systems and keeps equipment running reliably.
For operators, that means fewer replacements, lower maintenance costs, less downtime, and improved job site efficiency and safety — even in long-term outdoor, heavy-load, and wide-temperature-range environments.
Fits excavators, loaders, bulldozers, road rollers, concrete pump trucks, and other mainstream construction machines. Used in hydraulic power transmission, cylinder extension/retraction, steering, and braking systems. Built to handle on-site sand and gravel abrasion, frequent bending, and high-pressure surges in open-air working environments.
Suitable for roadheaders, crushers, mine haul trucks, hydraulic supports, and similar equipment. Withstands high dust, heavy abrasion, and high-pressure heavy-load conditions found in mining. Resists dust particle scouring and hydraulic oil exposure, preventing line leakage and failure.
Matches hydraulic systems on large tractors, combine harvesters, tillage equipment, and other farm machinery. Handles muddy field conditions, direct sun exposure, and frost. Oil-resistant and aging-stable, it copes with the frequent start-stop and moderate-bend cycles typical of agricultural equipment.
Used with industrial hydraulic machine tools, overhead cranes, conveyors, hydraulic power units, and other general industrial equipment. Built for continuous high-intensity factory operation, reliably transferring mineral-based hydraulic oils, lubricants, and similar media across a range of high-pressure fluid transfer applications.
Double or multi-layer high-tensile steel wire braid reinforcement, manufactured to SAE J517 industry standards. Standard working pressure ranges from 21 to 42 MPa, with a burst pressure four times the working pressure. Pressure stability exceeds standard hoses, handling the repeated pressure pulses of construction machinery without bulging, bursting, or pressure loss.
Inner tube made of premium NBR (nitrile butadiene rubber) with oil resistance meeting ASTM Type 1 standards. Compatible with mineral hydraulic oils, lubricants, and emulsions over extended contact. Retains over 90% of its physical properties after 20,000 hours of continuous operation, resisting swelling, cracking, and seepage in long-term hydraulic oil service.
Thickened, weather-resistant synthetic rubber outer cover with a specialized abrasion-modified formulation. Abrasion performance is roughly 3× that of standard rubber hoses, standing up to sand, gravel, dust, and mechanical rubbing. Service life exceeds 5,000 hours in harsh conditions, reducing line failures from wear-through.
Operates reliably across -40°C to +121°C. Stays flexible without becoming brittle in cold conditions; does not soften or deform at high temperatures. Also resists UV, ozone, and aging — suitable for prolonged outdoor exposure and environments with large day-night temperature swings, year-round.
The hose bends easily with a tight minimum bend radius, fitting into the confined spaces on construction equipment. Bending does not cause collapse or flow restriction. Impulse fatigue life exceeds 1 million cycles, maintaining performance through frequent start-stop and high-frequency pressure cycles — extending the overall service life of oil-resistant abrasion-proof hydraulic hoses for construction machinery.
|
Parameter |
Specification |
|
Pressure Rating |
Standard 21–42 MPa; higher-pressure custom versions available; burst pressure = 4 × working pressure |
|
Inner Diameter |
6 mm – 51 mm (non-standard diameters available on request) |
|
Standard Length |
20 m / 30 m per length; custom cut to any required length |
|
Construction |
Inner tube: NBR oil-resistant rubber; Reinforcement: high-tensile steel wire braid; Outer cover: abrasion-resistant synthetic rubber |
|
Operating Temperature |
-40°C to +121°C |
· Inspect the oil-resistant and wear-resistant hydraulic hoses for construction machinery before installation — do not use any hose with cracks, bulges, or visible damage.
· Avoid forcing, twisting, or over-bending during installation. Never exceed the rated pressure or temperature limits. Do not substitute a low-pressure hose in a high-pressure application — this creates a burst hazard.
· During use, keep hoses clear of sharp edges, high-heat sources, and corrosive acid/alkali media to reduce friction and crushing damage.
· Periodically check fitting seals and outer cover wear. Clean surface dust and oil buildup to prevent gradual degradation of the hose body from accumulated contaminants.
· Select the correct hose specification based on actual working pressure, media type, and operating temperature. Do not mix with non-standard or mismatched products.
· For long-term equipment storage, drain residual fluid from the hose and protect it from dust and direct sun to prevent premature aging.
· Replace hoses promptly at the first sign of cracking, seepage, hardening, deformation, or when impulse life ratings are reached. Operating a worn or damaged hose risks hydraulic system failure — replace proactively to keep equipment running safely.
Q: Is there a minimum order quantity?
A: Standard sizes are kept in stock and available for small or individual orders — no strict MOQ for off-the-shelf specifications. Custom non-standard hoses can be produced to your requirements, with volume-based pricing for larger construction project orders.
Q: What customization options do you offer?
A: We offer both OEM and ODM custom manufacturing. Hoses can be built to your specifications for inner diameter, length, pressure rating, and end-fitting style, based on your equipment's operating conditions or technical drawings. Brand logo printing and specification marking are also available.
Q: How is quality controlled on these hoses?
A: Every hydraulic hose undergoes pressure testing, abrasion inspection, and seal integrity checks before shipment. We manufacture to SAE J517 standards and run batch verification of inner tube oil resistance, burst pressure, and impulse cycle life to confirm performance meets specification.
Q: What warranty is provided?
A: All oil-resistant abrasion-proof hydraulic hoses for construction machinery are covered against manufacturing defects under normal use. We provide technical follow-up throughout the service period and respond promptly to any after-sales issues.
Q: Can you help with hose selection for specific equipment?
A: Yes. Share your equipment type, working pressure, fluid media, operating temperature, and required length, and our technical team will recommend the right hose specification and fitting configuration for your application.
Q: Do you supply hose assemblies with fittings already attached?
A: We can supply hose assemblies crimped with matching end fittings — ready to install on your equipment. Send us your fitting type and specifications and we'll provide a quote for complete assemblies.
Hengshui Zhehan Rubber & Plastic Products Co., Ltd. has specialized in hydraulic hose R&D and production for years, with mature manufacturing processes, consistent quality, and competitive pricing. We provide end-to-end support — from product selection and application matching to custom fabrication — for construction, mining, agricultural, and industrial customers.
We welcome new and returning customers to reach out for quotes, samples, or to arrange a factory visit and discuss partnership opportunities.
Address
No. 7126, Zhanggehou Rubber & Plastic Base, Jingzhou Town, Jing County, Hengshui City, Hebei Province, Chinaa
Tel
